-
Fiber dağıtım kutusu
-
FTTH Dağıtım Kutusu
-
Kablo Dağıtım Kutusu
-
LSA Plus Modülü
-
MDF Ana Dağıtım Çerçevesi
-
Abone Terminal Bloğu
-
rack mount patch panel
-
Rj45 Keystone Jack
-
Yatay kablo yöneticisi
-
ağ kablosu aynası
-
110 terminal bloğu
-
ODF Optik Dağıtım Çerçevesi
-
fiber optik patch kablosu
-
Fiber optik Splice kapatma
-
IDC Terminal Bloğu
-
Ağ Punch Down Tool
-
Fiber optik Aksesuar
-
ONU OLT
-
sıcaklığa duyarlı etiketler
-
Andreas SandvikÇok deneyimli üretici! -
Kristober GomezGüvenebileceğiniz Güvenilir, Güvenilir ve Deneyimli Bir Üretici -
ilker ErimezTelekomünikasyon tam çözümleri verdi. -
احمد عبداللهİran telekomünikasyon için kullanılan AMP TYCO picabond konektörleriniz mükemmel çalışıyor, müşterimiz kaliteden çok memnun.
Black Subscriber Terminal Block With / Without Protection Against Overvoltage
Ücretsiz numuneler ve kuponlar için benimle iletişime geçin.
Naber:0086 18588475571
sohbet: 0086 18588475571
Skype: sales10@aixton.com
Herhangi bir endişeniz varsa, 24 saat çevrimiçi yardım sağlıyoruz.
x| name | Subscriber Terminal Block | Environment condition | 5-40 degree Celsius ,Relative humidity <85% (+30 degree Celsius),Atmospheric pressure, 70-106KPa |
|---|---|---|---|
| plate | silver 20-40uinch | pulling-out force | not less than 25N |
| standard | GB/T 5169.7-1985 | material | pc |
| Vurgulamak | vx module,stb module |
||
1-Pair Drop Wire (STB) Module Without Protection is a copper pair connector specifically designed to fit onto 35mm DIN rails, It is designed to connect 2 copper pairs and has common features such as:
1. Water proof, sealed IDC termination
2. Disconnection and testing facilities
3. Tooless termination
4. 5 point protection plug with 1×3-pole GDT 230V 5A/5KA and 2×PTCRs in
| Range of the section: | diameter 0,4… 1,2 mm |
| Diameter on the isolation: | it is maximal 5 mm |
| The current-response characteristics: | 20 A(10 A on each conductor) during not less than 10 min, without the deformation of the module |
| Insulation resistance | |
| “Dry” atmosphere: | > 10 12 Ohm |
| “Moist” atmosphere (standard ASTM Of d618, procedure F): | > 10 12 Om |
| Salt fog: (standard ASTM Of b117) | > 10 10 Ohm |
| Immersion beside the water: (15 days before 3% solution Of naCI) | > 10 10 0m |
| The contact resistance | |
| R of material + R of the contact cross connection + by R of the contact connection of the wires | < 10 m |
| Increase in the contact resistance | |
| After climatic testings: | <2,5 m |
| After 50 connections - turning offs: | <2,5 m |
| Dielectric strength: | >3 kV of direct current during 1 minute |
Mechanical characteristics
| Screw of the connection of the pair of the distributive wire: | Special alloy Of zamac, [passivirovannyy], with the paint and varnish coat |
| Housing of the unit of the connection | Transparent polycarbonate |
| the distributive wire: Housing: | Polycarbonate, glass-reinforced, resistance to fire “VO” |
| Fitted contacts: | Tinplated phosphor bronze |
| Contacts of the grounding: | Alloy Cu - Zn - Ni - Ag |
| Contacts of the connection: | Tinplated solid bronze |
| Sealing material before the lower part: | The epoxy resin |
| Sealing material before the upper cable part: | Silicon compound |
| Cover of the pair of the distributive wire: | Polycarbonate |
| Housing of the insertable module: | Polycarbonate, glass-reinforced, resistance to fire “VO” |
| Sealing material of the insertable module: | Gel |
| The ring gasket: | Elastomer EPDM |
| Spring: | the stainless steel |
| Cable laying is the distributive wire: | Thermoplastic rubber |

